Knock-down Hutch

Materials: Fir, Plywood, Pine (cheap wood!).

Finish: Lexington Green milk paint and linseed oil.

Several years ago, Masters Robyyan Torr d'Elandris and Terafan Greydragon developed plans for a knock-down panel chest. "Why would someone want a box that breaks apart?" you might ask. Well, they are particularly useful when one needs a large box that can be transported in a not-so-large vehicle. The most common application is for hiding coolers in a period encampment, though having used one for a week of camping I now see the potential for many other storage applications.

This year I decided I was tired of looking at coolers with blankets thrown over them, and in a fit of dubious ambition, undertook to build a knock-down chest of suitable size for a large cooler (and a few odds and sods to boot). The result was a passably medieval hutch. One thing I like about this design is that no plywood edges are visible, making it look more like real furniture.

Robyyan's original was a faux-panel chest (an entirely period concept when cheaper boarded chests were made to resemble more desireable frame-and-panel construction). I decided to take a different tact and build one in the style of a hutch. The hutch is an earlier form of chest that was used well into the modern era, giving it a wide period of applications. The hutch uses what is referred to as "clamped-front" joinery. In this design, wide vertical legs (or "stiles") are mortised to receive large boards that make up the front and sides of the chest. The hutch shows up by the 14th century, and continues in use through the 19th century, in later times for grain storage. When used as a grain bin, they often had a domed lid that could be removed and used as a dough trough. I wasn't that ambitious.

This being a camp project, I wanted to keep costs to a minimum, and not being a "period" project, modern materials and expedients were just fine. I began with a quick visit to the local home supply store for the following:

First, cut the front and end panels from the plywood sheets. From each sheet, I cut one panel 29 inches by 20 inches, and one 19 inches by 20 inches. Mine are proportioned to fit a large Coleman cooler, leaving sufficient space for the lid to open and a little extra dry storage. You can use other proportions, but in general hutches tend to be more boxy than panel chests. Cut carefully so your panels are identical and the corners are square.

Next, make the stiles. Cut four pieces of 2 x 8 to equal length (mine are 28 inches long, which makes a 20 inch box on top of 8 inch legs).

There are a number of ways you can do the following step. I used a tablesaw with a stacked-dado cutter; you can also use a router, or if you've got more time than tools, you can use hand chisels. You could also build up the stiles by gluing up 1-inch boards.

On each stile, you will need to cut a dado to hold the end panel, and a rabbet to hold the front panel. The dado should should be wide enough that the panel slides in and out easily, and no deeper than half the board thickness. Try each panel for fit before assembly, as it is harder to make adjustments after you have assembled everything. The rabbet should be just deep enough so the front panel will lay flush to the inside of the stile, and at least 3 inches wide. DO NOT make four identical stiles: the left and right sides are mirror images of each other.

Give everything a good sanding, and round off any sharp corners. Pine and fir are prone to chipping and splintering, but less so if you camfer the edges.

Assemble the front and back of the hutch using wood glue and screws. It's a good idea to counter-sink the screws so you have a nice smooth surface on the inside. Let the glue set.

To hold in the floor, you will need to attach a cleat around the inside of the bottom. I ripped down some scrap into strips about 3/4-inch square and attached with wood glue and screws.

Now you're ready to assemble. Slide the pieces together and make sure everything fits.

Obviously, you need fasteners to hold everything together. Terafan and Robyyan used hinges with removeable pins, relying on the bottom panel to keep everything square. . I wanted something that would add some stability, so I used sliding panel brackets, available from Lee Valley and other vendors. They also have right-angle assembly plates (cheaper!), that would serve the same purpose.

For the bottom, I used four 1 by 10 pine boards cut to length (old shelves I had laying around the shop). You could just as easily use a sheet of plywood or particle board, as no part of the bottom is visible from the outside. If you plan on using your hutch to hide a cooler, I suggest attaching some battens across the bottom and boring some ventilation holes between them. Coolers tend to sweat and by the end of a week at Pennsic things may get a bit moldy if you don't allow for ventilation.

For the top, I wanted to use solid wood instead of plywood. Wide boards of glued-up stock are available at most home centers at reasonable prices. Again, try to find a piece with minimal knots and filler. I attached cleats across the inside to keep the top from warping over time. If you use plywod, run a band of molding around the edges so it doesn't look so much like plywood. Screw the hinges in place, then just knock the pins out when you want to disassemble it.

To finish the hutch, I used Lexington Green milk paint. You could try a stain, but I generally find that stained plywood looks like, well, stained plywood. Milk paint has an advantage over most other paints in that it penetrates the wood surface instead of forming a hard shell on top of it. Given that this hutch will get thrown in the truck and knocked around, the milk paint will be less prone to chipping and peeling. I cover the milk paint with a few coats of linseed oil, which mellows the color of the paint and helps provide some protection against water spots. It also helps keep the plywood from swelling in humidity.

I also suggest giving the bottom panel a couple of coats of polyeurathane. While I normally shy away from "plastic" finishes, the bottom may see a lot of moisture and needs a good waterproof finish.

Additional improvements I plan to include are a prop to keep the lid open, a stop chain to prevent the lid from falling too far open (and ripping out the hinges), and a small removable shelf so there is somewhere to set cups while rummaging in the cooler. A bottle opener mounted inside would also be helpful.

When not in use, I've found this hutch makes a serviceable chest in which to store our pavillion canvas, keeping it out of any moisture and away from nibbling bugs or rodents.

You can find Master Robyyan's original plans here:

http://robyyan.home.mindspring.com/articles/breakdown.html

And Terafan Greydragon's elaboration here:

http://www.greydragon.org/furniture/panelchests.html

 

Return to the Blood and Sawdust Projects Index

 

 

Copyright 2006, Tom Rettie. Content may not be republished in any form without permission of the author.